119 Castlehaven Road, Camden, London NW1 8SJinfo@neosengineering.comCall 020 3780 0788or text 07575 561 698Get a price

Unvented cylinders at business premises: servicing and rules

27 October 2026 · Neos Engineering, Gas Safe registered, Camden

An unvented hot water cylinder at a business should be serviced once a year by an engineer qualified to work on unvented systems. Most makers ask for that yearly service to keep the guarantee, and it is the visit that proves the safety valves still work. The law also asks for the cylinder to have been fitted by a qualified installer, and for the water it stores to be kept hot enough to control legionella.

What an unvented cylinder is

An unvented cylinder is fed straight from the mains, with no cold water tank in the loft. It stores hot water under pressure, so every tap and shower gets mains pressure hot water. Offices, hotels, restaurants and shops use them because they save space and give a strong flow to many outlets at once.

Storing hot water under pressure is also why they come with safety devices. If the controls failed and nothing else stopped it, the water could heat past boiling point while under pressure.

What the rules ask

In England, requirement G3 of the Building Regulations (Approved Document G) covers unvented hot water. For a cylinder holding more than 15 litres:

  • It must be installed by a competent person, usually called G3 qualified, and the work notified to building control or through a competent person scheme.
  • It must have at least two independent safety devices beyond the thermostat: an energy cut out that does not reset itself, and a temperature relief valve, usually combined with pressure relief in one temperature and pressure relief valve.
  • Water released by those valves must run through a tundish, where it can be seen, to a safe place to discharge.

At work, HSE’s legionella guidance applies as well. Stored hot water should be kept at 60°C or above, and reach at least 50°C at the outlets within one minute (55°C in healthcare premises). Whoever controls the premises needs a legionella risk assessment. The cylinder service sets and checks the temperatures; the assessment itself is a separate job.

What a yearly service covers

Part What the engineer checks
Expansion vessel or air bubble The air charge, topped up if it has dropped
Pressure reducing valve and inlet strainer Incoming pressure, strainer cleaned
Expansion relief valve Operated by hand, checked it seats and does not drip
Temperature and pressure relief valve Operated by hand, checked it reseats
Tundish and discharge pipe Clear, visible, and running to a safe place
Thermostat and energy cut out Both work, and the stored temperature is right
Cylinder and connections Leaks, corrosion and scale

London water is hard. Scale builds up on the heating coil, the immersion heater and the valves, and a cylinder that has not been looked after for years often needs a full strip down and descale rather than a standard service.

Warning signs to act on

  • Water dripping or running from the tundish. A safety valve is letting water go. Often the expansion vessel has lost its charge, but it should be checked soon.
  • Hot water or steam from the tundish. The cylinder is overheating. Switch off the boiler and the immersion heater that heat it, keep people clear of the discharge, and call an engineer.
  • Pressure at the taps rising and falling, or the cold supply pressure changing when hot taps run.
  • Hot water running cold early, or taking much longer than usual to recover.
  • Banging or hissing from the cylinder or its pipework.

Who can work on it

Only an engineer qualified for unvented hot water storage should service or repair it. Where a boiler heats the cylinder, the gas side needs a Gas Safe registered engineer too. Ask for the service record each year and keep it with the boiler records for the same building.

Servicing in London

Neos Engineering services and repairs unvented cylinders at business premises across London. A service is £300 + VAT (£360 inc VAT) per cylinder, including the safety valve checks and recharging the expansion vessel. A full strip down and descale is quoted by the size of the cylinder. Pipework and hot water systems are covered on our commercial plumbing page, and the boilers that heat them on our commercial boiler service page.

If you need us

Rather just ask an engineer?

Call any hour, email us, or get a price in under a minute. The hourly rate is confirmed when you book. A call out is charged by the hour, and a return visit or further work is quoted first.